View LTW-M670ZVS-M5_4575120.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only Features
* * * * * * Package in 8mm tape on 7" diameter reels. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow solder process. EIA STD package. I.C. compatible. Meet green product and Pb-free(According to RoHS)
Package
Dimensions
Part No. LTW-M670ZVS-M5
Lens Color Yellow
Source Color InGaN White
Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.2 mm (.008") unless otherwise noted.
Part No. : LTW-M670ZVS-M5 BNS-OD-C131/A4
Page :
1
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only Absolute Maximum Ratings at Ta=25
Parameter Power Dissipation Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) DC Forward Current Reverse Voltage Operating Temperature Range Storage Temperature Range Wave Soldering Condition Suggest IR Reflow Condition :
LTW-M670ZVS-M5 120
Unit mW
100
mA
30 5 -30 to + 85 -40 to + 100 260 For 5 Seconds
mA V
IR-Reflow Soldering Profile for lead free soldering (Acc. to J-STD-020B)
Part No. : LTW-M670ZVS-M5 BNS-OD-C131/A4
Page :
2
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only Electrical Optical Characteristics At Ta=25
Parameter
Symbol
Part No. LTWM670ZVS-M5
Min.
Typ.
Max.
Unit
Test Condition IF = 20mA Note 1, 2, 5 IF = 20mA Note 1, 2, 5 Fig.6 IF = 20mA Note 3, 5 Fig.1
Luminous Intensity
IV
1500
-
2000
mcd
Luminous Flux
V
M670ZVS-M5
4500
mlm
Viewing Angle
21/2 x
M670ZVS-M5
120 0.29
deg
Chromaticity Coordinates y Peak Wavelength Wp
M670ZVS-M5 0.27 M670ZVS-M5 450 nm
IF = 20mA
Forward Voltage
VF
M670ZVS-M5
3.0
3.3
3.5
V
IF = 20mA
ESD-Withstand Voltage
ESD
M670ZVS-M5
2K
V
HBM
Note: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. 2. Iv classification code is marked on each packing bag. 3. The chromaticity coordinates (x, y) is derived from the 1931 CIE chromaticity diagram. 4. Caution in ESD: Static Electricity and surge damages the LED. It is recommended using a wrist band or anti-electrostatic glove when handling the LED. All devices, equipment and machinery must be properly grounded. 5. CAS140B is the test standard for the chromaticity coordinates (x, y) & IV. 6. The chromaticity coordinates (x, y) guarantee should be added 0.01 tolerance.
Part
No. : LTW-M670ZVS-M5
Page :
3
of
11
BNS-OD-C131/A4
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only Bin Code List
VF Bin V1 V2 V3 V4 V5
VF Spec. Table Forward Voltage (V) at IF = 20mA Min. 3.0 3.1 3.2 3.3 3.4 Max. 3.1 3.2 3.3 3.4 3.5
Tolerance on each Forward Voltage bin is +/-0.10 volt IV Spec. Table IV Bin S51 S52 S61 S62 S71 S72 S81 S82 S91 S92 IV (mcd) at IF = 20mA Min. 1500 1550 1600 1650 1700 1750 1800 1850 1900 1950 Max. 1550 1600 1650 1700 1750 1800 1850 1900 1950 2000
Tolerance on each Luminous Intensity bin is +/- 10%. Color Ranks Table Ranks B C F G x y x y x y x y Color bin limits at IF = 20mA CIE 1931Chromaticity coordinates 0.279 0.262 0.279 0.252 0.289 0.280 0.289 0.270 0.279 0.252 0.279 0.242 0.289 0.270 0.289 0.261 0.289 0.270 0.289 0.261 0.299 0.288 0.299 0.278 0.289 0.280 0.289 0.270 0.299 0.298 0.299 0.288
Tolerance on each Hue (x, y) bin is +/- 0.01.
Part
No. : LTW-M670ZVS-M5
Page :
4
of
11
BNS-OD-C131/A4
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Rank (X,Y) 0.32
0.30
0.28
F G
0.26
B C
0.24
0.22 0.26 0.27 0.28 0.29 0.30 0.31 0.32
Part
No. : LTW-M670ZVS-M5
Page :
5
of
11
BNS-OD-C131/A4
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only Typical Electrical / Optical Characteristics Curves (25 C Ambient Temperature Unless Otherwise Noted)
Relative Intensity
1.0
0.5
0.0 350 450 550 650 750 wavelength (nm) Fig.1 RELATIVE INTENSITY VS. WAVELENGTH
Part No. : LTW-M670ZVS-M5 BNS-OD-C131/A4
Page :
6
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only User Guide Cleaning
Do not use unspecified chemical liquid to clean LED they could harm the package. If cleaning is necessary, immerse the LED in ethyl alcohol or isopropyl alcohol at normal temperature for less than one minute. Recommend Printed Circuit Board Attachment Pad Infrared / vapor phase Reflow Soldering
Package Dimensions of Tape
Note: 1. All dimensions are in millimeters (inches).
Part No. : LTW-M670ZVS-M5 BNS-OD-C131/A4
Page :
7
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only Package Dimensions of Reel
Notes: 1. Empty component pockets sealed with top cover tape. 2. 7 inch reel-2000 pieces per reel. 3. Minimum packing quantity is 500 pieces. 4. The maximum number of consecutive missing lamps is two. 5. In accordance with EIA-481-1-B specifications.
Part No. : LTW-M670ZVS-M5 BNS-OD-C131/A4
Page :
8
of
11
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
CAUTIONS
1. Application The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications).Consult Liteon's Sales in advance for information on applications in which exceptional reliability is required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safety devices). 2. Storage This product is qualified as Moisture sensitive Level 3 per JEDEC J-STD-020 Precaution when handing this moisture sensitive product is important to ensure the reliability of the product. The package is sealed: The LEDs should be stored at 30C or less and 90%RH or less. And the LEDs are limited to use within one year, while the LEDs is packed in moisture-proof package with the desiccants inside. The package is opened: The LEDs should be stored at 30C or less and 60%RH or less. Moreover, the LEDs are limited to solder process within 168hrs. If the Humidity Indicator shows the pink color in 10% even higher or exceed the storage limiting time since opened, that we recommended to baking LEDs at 60C at least 48hrs. To seal the remainder LEDs return to package, it's recommended to be with workable desiccants in original package. 3. Cleaning Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED if necessary. 4. Soldering Recommended soldering conditions: Reflow soldering Wave Soldering
Pre-heat 120~150C Pre-heat time 120 sec. Max. Soldering Temp. 260C Max. Soldering time 30 sec. Max. Pre-heat Pre-heat time Solder wave Soldering time 100C Max. 60 sec. Max. 260C Max. 10 sec. Max.
Soldering iron
Temperature Soldering time 300C Max. 3 sec. Max. (one time only)
5. Drive Method An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with each LED as shown in Circuit A below. Circuit model A
LED
Circuit model B
LED
(A) Recommended circuit. (B) The brightness of each LED might appear different due to the differences in the I-V characteristics of those LEDs. 6. ESD (Electrostatic Discharge) Static Electricity or power surge will damage the LED. Suggestions to prevent ESD damage: Part No. : LTW-M670ZVS-M5 Page : 9 of 11
BNS-OD-C131/A4
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only Use of a conductive wrist band or anti-electrostatic glove when handling these LEDs. All devices, equipment, and machinery must be properly grounded. Work tables, storage racks, etc. should be properly grounded. Use ion blower to neutralize the static charge which might have built up on surface of the LED's plastic lens as a result of friction between LEDs during storage and handling. ESD-damaged LEDs will exhibit abnormal characteristics such as high reverse leakage current, low forward voltage, or "no lightup" at low currents. To verify for ESD damage, check for "light up" and Vf of the suspect LEDs at low currents. The Vf of "good" LEDs should be >2.0V@0.1mA for InGaN product and >1.4V@0.1mA for AlInGaP product. 7. Reliability Test
Test Item
Resistance to Soldering Heat (Reflow Soldering) Solderability (Reflow Soldering) Thermal Shock Temperature Cycle High Temperature Storage Temperature Humidity Storage Low Temperature Storage Steady State Operating Life Condition 1 Steady State Operating Life Condition 2 Steady State Operating Life of High Temperature Steady State Operating Life of High Humidity Heat Steady State Operating Life of low Temperature
Test Condition
Tsld=260, 10sec. Tsld=2455, 3sec. (Lead Free Solder) -30 ~ 85 30min.. 30min. -40 ~ 25 ~ 100 ~ 25 30min. 5min. 30min. 5min. Ta=100 Ta=60, RH=90% Ta=-40 Ta=25, IF=20mA Ta=25, IF=30mA
Reference Standard
JEITA ED-4701 300 301 JEITA ED-4701 300 303 JEITA ED-4701 300 307 JEITA ED-4701 100 105 JEITA ED-4701 200 201 JEITA ED-4701 100 103 JEITA ED-4701 200 202
Note
2 times 1 time Over 95% 100 cycles 100 cycles 1000 hrs. 1000 hrs. 1000 hrs. 1000 hrs. 500 hrs.
Number of Damaged
0/30 0/30 0/30 0/30 0/30 0/30 0/30 0/30 0/30
Ta=85, IF=5mA
1000 hrs.
0/30
60, RH=90% , IF=15mA
500 hrs.
0/30
Ta=-30, IF=20mA
1000 hrs.
0/30
Part
No. : LTW-M670ZVS-M5
Page :
10
of
11
BNS-OD-C131/A4
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only 8. Others The appearance and specifications of the product may be modified for improvement without prior notice. 9. Suggested Checking List Training and Certification 1. Everyone working in a static-safe area is ESD-certified? 2. Training records kept and re-certification dates monitored? Static-Safe Workstation & Work Areas 1. Static-safe workstation or work-areas have ESD signs? 2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V? 3. All ionizer activated, positioned towards the units? 4. Each work surface mats grounding is good? Personnel Grounding 1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 2. If conductive footwear used, conductive flooring also present where operator stand or walk? 3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*? 4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DLs? 5. All wrist strap or heel strap checkers calibration up to date? Note: *50V for Blue LED. Device Handling 1. Every ESDS items identified by EIA-471 labels on item or packaging? 2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe workstation? 3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items? 4. All flexible conductive and dissipative package materials inspected before reuse or recycle? Others 1. Audit result reported to entity ESD control coordinator? 2. Corrective action from previous audits completed? 3. Are audit records complete and on file?
Part
No. : LTW-M670ZVS-M5
Page :
11
of
11
BNS-OD-C131/A4

▲Up To Search▲

Price & Availability of LTW-M670ZVS-M5

	To Download LTW-M670ZVS-M5 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .